Load data for .375 SOCOM + .374 | 250gr | Rhino Solid Shank

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.374 \| 250gr \| Rhino Solid Shank
Bullet Weight:	250gr \| 16.2g
Bullet Diameter:	0.374" \| 9.50mm
Bullet Length:	1.225" \| 31.1mm
Caliber:	.375 SOCOM load data
Case Length (l3):	1.575" \| 40.0mm
Cartridge Length (C.O.L.):	2.226" \| 56.5mm
Seated Depth:	0.574" \| 14.6mm
Shank Seated Depth:	0.574" \| 14.6mm
Case Capacity:	60.0 Grains of Water \| 3.90 cm³
Primer Size:	Large Pistol Magnum (LPM)
Max. allowed Pressure:	34954 psi \| 2410 bar
LID:	LID_B5256_C570
Last updated:	2025-02-02

Load data for 40 loads in caliber .375 SOCOM with .374 | 250gr | Rhino Solid Shank bullet and 20 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AR 2219]*	<<locked>>	84%	31212	89%	**78	93%
Accurate 2015	<<locked>>	90%	30995	89%	**72	96%
Accurate 2495	<<locked>>	97%	29312	84%	**37	96%
Alliant AR-Comp	<<locked>>	93%	31096	89%	**24	98%
Alliant Reloder-10x	<<locked>>	87%	31241	89%	**88	97%
[Hodgdon H322]*	<<locked>>	89%	30951	89%	**72	93%
[Hodgdon H335]*	<<locked>>	85%	31154	89%	**78	92%
[IMR 3031]*	<<locked>>	96%	29356	84%	**85	94%
IMR 4198	<<locked>>	83%	31444	90%	**32	98%
[Norma 202]*	<<locked>>	95%	31343	90%	**95	92%
[Rottweil R 901]*	<<locked>>	91%	30850	88%	**52	92%
[SNPE Vectan SP 10]*	<<locked>>	84%	31024	89%	**75	92%
[SNPE Vectan Tubal 3000]*	<<locked>>	92%	31314	90%	**16	92%
[SNPE Vectan Tubal 5000]*	<<locked>>	96%	29559	85%	**86	92%
[Somchem S335]*	<<locked>>	93%	31125	89%	**39	94%
Vihtavuori N130	<<locked>>	87%	30748	88%	**26	97%
Vihtavuori N133	<<locked>>	94%	31140	89%	**36	96%
[Vihtavuori N135]*	<<locked>>	97%	24787	71%	**50	92%
[Vihtavuori N140]*	<<locked>>	96%	31111	89%	**62	92%
[Vihtavuori N540]*	<<locked>>	97%	31140	89%	**88	92%

Max Load - Barrel Length: 23.60''

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AR 2219]*	<<locked>>	81%	28427	81%	**13	92%
[Accurate 2015]*	<<locked>>	81%	23656	68%	**08	93%
[Accurate 2495]*	<<locked>>	85%	19885	57%	**98	90%
[Alliant AR-Comp]*	<<locked>>	81%	21321	61%	**68	93%
Alliant Reloder-10x	<<locked>>	81%	26426	76%	**80	96%
[Hodgdon H322]*	<<locked>>	83%	25512	73%	**41	90%
[Hodgdon H335]*	<<locked>>	82%	28340	81%	**16	90%
[IMR 3031]*	<<locked>>	90%	24395	70%	**54	90%
IMR 4198	<<locked>>	81%	29240	84%	**86	97%
[Norma 202]*	<<locked>>	90%	27209	78%	**03	90%
[Rottweil R 901]*	<<locked>>	87%	27441	79%	**77	90%
[SNPE Vectan SP 10]*	<<locked>>	81%	28326	81%	**19	91%
[SNPE Vectan Tubal 3000]*	<<locked>>	87%	27064	77%	**27	90%
[SNPE Vectan Tubal 5000]*	<<locked>>	92%	25599	73%	**95	90%
[Somchem S335]*	<<locked>>	85%	24787	71%	**01	90%
Vihtavuori N130	<<locked>>	81%	25251	72%	**04	95%
[Vihtavuori N133]*	<<locked>>	82%	21930	63%	**13	90%
[Vihtavuori N135]*	<<locked>>	93%	22684	65%	**91	90%
[Vihtavuori N140]*	<<locked>>	92%	27151	78%	**73	90%
[Vihtavuori N540]*	<<locked>>	94%	28355	81%	**26	90%

Start Load - Barrel Length: 23.60''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data